SARAMONIC MIXMIC

Inputs:
One 1/8″ (3.5 mm) Auxiliary Mini-Jack Input
Two balanced XLR inputs
Output:
One stereo 1/8″ (3.5 mm) Mini-Jack Output
Dual Trim Control Knobs:
Adjust the signal of each channel to the optimum recording level
Mono /Stereo Switch:
LINE / MIC Switch:
GND1/GND2 Ground switch eliminate ground hum and noise
No Powe or Battery is Needed Input Level:
MIC：-35 dBu

LINE：-10 – +4 dBu

Input Level:General Mic Levels

Frequency Response:10Hz to 100kHz (+/-1.5 dB)

Dimensions:87 (L) x 80(W) x 52(H) mm

Weight:191g (6.7oz.)

Cardioid broadcast sound quality
1400 mAh internal rechargeable lithium battery
Balanced output
+48V phantom power
High frequency boost button
High pass filter (150 Hz)
Signal to noise ratio:75 dB SPL (per IEC651)
-10 dB PAD button Acoustic Principle:Line gradient
Directional Pattern:Cardioid

Frequency Range:40 to 20k Hz (selectable HPF 150 Hz)

Sensitivity:-35±3dB(0dB=1V/Pa,at 1KHz) 1.5V 2.2kΩ

Output Impedance:200 ohm

Maximum Output:10 dBu (at 1 kHz, 1% THD into 1 kOhm)

Dynamic Range:119 dB (per IEC651)

Maximum SPL:135 dB

Signal to Noise Ratio:75 dB SPL (per IEC651)

Power:48V phantom power;

built-in lithium battery;

(battery life:150 hours)

Output Connection;

3-pin XLR

balanced output between Pin 2 (+)

Pin 3 (-) and Pin 1 (ground)

Dimensions:2.3 x 2.3 x 28.2 cm

Weight:171g (About 6 oz.)

Maximum SPL:135 dB

Improves audio quality of smart phone
Two 1/8’’ (3.5mm) stereo mic/line inputs
One mini XLR microphone input (a mini-XLR to standard-XLR cable included)
+48V phantom power
One 1/8’’ (3.5mm) stereo line output to phone
One 1/8’’ (3.5mm) headphone monitor output
PLAY/REC monitor switch
Independent L/R level meters
Volume control knob
Includes two plug-in power condenser microphones
Includes a device holder and aluminum hand grip
Power provided by 9V battery Frequency Response: 20 Hz to 20 Khz, +/-0.5 dB
SNR: 82 dB @ 1 kHz, -30 dBu input

Distortion: Less than 0.03% @ 1 kHz, -30 dBu input

INPUT 1 GAIN: 15 dB

INPUT 2 GAIN & MINI XLR Jack: 15 dB

INPUT 1 & INPUT 2 Power: 5V power supplies

MINI Jack Phantom Power: 48V power supplies

VU Meter: -18 dB to +3 dB in 3 dB increments

Power Requirements: 9V alkaline or lithium battery

Dimensions: L 95 x W35 x H298 mm

Weight: 0.74 kg (26.1 oz.)

Compatible with the receiver of SR-WM4C wireless system
Four switchable channels to keep you free from interference
Handheld design for recording applications like interview
The high-band VHF provides pure sound
Record audio up to 60 metes away with no obstacle
Real-time monitoring
Volume control wheel
Power provided by LR6/AA size alkaline battery Operating Frequencies:
Channel A Channel B Channel C Channel D
203.65MHz 207.75MHz 211.55MHz 215.35MHz
Transmitters:
Operating Frequencies: 203-216MHz
Modulation Frequency: Modulation
Signal to noise ratio: 70dB or more
Antenna: 1/8λ wire antenna
Voice delay: 12ms
Battery: LR6/AA size alkaline Battery (not included)
Battery Life: 5 hours
Audio input connector: none
Current Consumption: 150 mA
Dimensions: L100.5*W43*H35mm
Weight: 137g (4.8 oz) without battery
Receiver:
Operating Frequencies: 203-216MHz
Reception System: FM Superheterodyne
Reception Sensitivity: 2 µV for 30 dB S/N
Output Connector: 3.5 mm (1/8″) TRS
DC Input: 9V DC (center-positive)
Battery: LR6/AA size alkaline Battery (not included)
Current Consumption: 150 mA
Battery Life: 5 hours
Dimensions: 102 x 62.0 x 44.7
Antenna Length: 178mm
Weight: 80 g (2.8 oz) without battery

Two balanced XLR inputs One monitor input jack
One stereo 1/8″ (3.5 mm) mini-jack output
Left and Right control knobs allows you to adjust the signal of each channel to the optimum recording levels
M/S Switch select mono or stereo output mode
LINE / MIC/ PH Switches
PH 12V/OFF/48V Switch
Level Meter indicates the sound level in dB for each channel
The LED signal indicators flash red for overload
Gain switch selects LOW for unity gain or HIGH for +20dB boost in sound level
Headphone jack to monitor the audio from microphones or camera
AGC ON/OFF Switch —Auto Gain Control will increase the gain to maximum level, the AGC Disable function reduces the hiss when the camera is recording during quiet moments
GND1/GND2 Dual-mode grounding switch
Dual Headphone Jacks allow you to monitor the audio from the adapter at the input and output points Maximum Input Levels：

MIC 0 dB on the Level meter at -44 dBu input

LINE 0 dB on the Level meter at +10 dBu input

Output Level:Nominal MIC levels

Frequency Response:20 Hz to 20 kHz (+/- 0.5 dB)

THD:Less than 0.01% @ 1kHz, -30dBu input

S/N Ratio:85 dB @ 1 Khz, -30 dBu input

Gain:

LO gain: 0 dB

HI gain: 20 dB

Phantom Power:

Dual regulated 12 or 48 volt power supplies

Current to 14 mA (direct short)

Level meter:

-18 to +3 dB in 3 dB increments

Battery Type:One 9 volt alkaline or lithium battery

Battery Duration:

3 hours typical with alkaline battery (no phantom)

8 hours typical with lithium battery (no phantom)

Dimensions:

(L x W x H) 155 mm x 98 mm x 64 mm

Weight:21.1 oz (0.599 kg)

• Output to both DSLR camera and smartphone
• 3.5mm TRS & TRRS output cables included
• Integrated shock mount
• Plug & Use Design
• Foam windscreen included
• Rugged alluminum alloy construction for main body Model :Vmic Mini

Type:14mm Unidirectional Condenser Microphone

Frequency Range :75Hz to 20kHz

Sensitivity:-35dB +/- 3dB (0dB=1V/Pa, at 1 KHz)

Maximum input S.P.L:f=1 kHz, THD<5% (105 dB)Output Impedance :200 ohmSignal to Noise Ratio:75 dB SPLPower :Plug-in powerDimensions:62 × 117 × 19mmWeight:69g (about 2.4oz)