Nic Mic BY- WM6

Cardioid broadcast sound quality
1400 mAh internal rechargeable lithium battery
Balanced output
+48V phantom power
High frequency boost button
High pass filter (150 Hz)
Signal to noise ratio:75 dB SPL (per IEC651)
-10 dB PAD button Acoustic Principle:Line gradient
Directional Pattern:Cardioid

Frequency Range:40 to 20k Hz (selectable HPF 150 Hz)

Sensitivity:-35±3dB(0dB=1V/Pa,at 1KHz) 1.5V 2.2kΩ

Output Impedance:200 ohm

Maximum Output:10 dBu (at 1 kHz, 1% THD into 1 kOhm)

Dynamic Range:119 dB (per IEC651)

Maximum SPL:135 dB

Signal to Noise Ratio:75 dB SPL (per IEC651)

Power:48V phantom power;

built-in lithium battery;

(battery life:150 hours)

Output Connection;

3-pin XLR

balanced output between Pin 2 (+)

Pin 3 (-) and Pin 1 (ground)

Dimensions:2.3 x 2.3 x 28.2 cm

Weight:171g (About 6 oz.)

Maximum SPL:135 dB

Optimised frequency response
Extreme low handling and wind noise
Excellent sound quality
Cardioid dynamic capsule
Rugged all-metal body Pick-up pattern:cardioid

Frequency Response:100Hz~10KHz

Sensitivity:0°~-52.4dB±3dB (0dB=1V/ubar at 1KHz)

Output Impedance:500Ω±30% at 1 KHz

Connector:3-pin XLR Connector

Dimensions:ø51 mm,length 258mm/approx.320g

Inputs:
One 1/8″ (3.5 mm) Auxiliary Mini-Jack Input
Two balanced XLR inputs
Output:
One stereo 1/8″ (3.5 mm) Mini-Jack Output
Dual Trim Control Knobs:
Adjust the signal of each channel to the optimum recording level
Mono /Stereo Switch:
LINE / MIC Switch:
GND1/GND2 Ground switch eliminate ground hum and noise
No Powe or Battery is Needed Input Level:
MIC：-35 dBu

LINE：-10 – +4 dBu

Input Level:General Mic Levels

Frequency Response:10Hz to 100kHz (+/-1.5 dB)

Dimensions:87 (L) x 80(W) x 52(H) mm

Weight:191g (6.7oz.)

Directional 90° mic capsule
Integrated shock-mount
Limits Background Noise
Foam Windscreen Included Type:Condenser microphones

Connector:TRRS (3.5mm jack) for iOS and Mac

Frequency Response:35 Hz to 18 kHz

Signal to Noise Ratio:74dB SPL

Dimensions:2.8 x 0.6 x 0.5 inches

Weight:21g (0.74oz)

Two balanced XLR inputs One monitor input jack
One stereo 1/8″ (3.5 mm) mini-jack output
Left and Right control knobs allows you to adjust the signal of each channel to the optimum recording levels
M/S Switch select mono or stereo output mode
LINE / MIC/ PH Switches
PH 12V/OFF/48V Switch
Level Meter indicates the sound level in dB for each channel
The LED signal indicators flash red for overload
Gain switch selects LOW for unity gain or HIGH for +20dB boost in sound level
Headphone jack to monitor the audio from microphones or camera
AGC ON/OFF Switch —Auto Gain Control will increase the gain to maximum level, the AGC Disable function reduces the hiss when the camera is recording during quiet moments
GND1/GND2 Dual-mode grounding switch
Dual Headphone Jacks allow you to monitor the audio from the adapter at the input and output points Maximum Input Levels：

MIC 0 dB on the Level meter at -44 dBu input

LINE 0 dB on the Level meter at +10 dBu input

Output Level:Nominal MIC levels

Frequency Response:20 Hz to 20 kHz (+/- 0.5 dB)

THD:Less than 0.01% @ 1kHz, -30dBu input

S/N Ratio:85 dB @ 1 Khz, -30 dBu input

Gain:

LO gain: 0 dB

HI gain: 20 dB

Phantom Power:

Dual regulated 12 or 48 volt power supplies

Current to 14 mA (direct short)

Level meter:

-18 to +3 dB in 3 dB increments

Battery Type:One 9 volt alkaline or lithium battery

Battery Duration:

3 hours typical with alkaline battery (no phantom)

8 hours typical with lithium battery (no phantom)

Dimensions:

(L x W x H) 155 mm x 98 mm x 64 mm

Weight:21.1 oz (0.599 kg)