BOYA BY-K3 – 3.5mm TRRS (Female) to Lightning (Male) Audio Adapter
Additional information
Brand |
---|
Get free shipping for order over 500EGP
BOYA BY-K3 – 3.5mm TRRS (Female) to Lightning (Male) Audio Adapter
Brand |
---|
Four switchable channels to keep you free from interference
Detachable and flexible antenna can be rotated 360 degrees acrdingly for best sound
The high-band VHF provides pure sound
Record audio up to 60 metes away with no obstacle
Real-time monitoring
Volume control wheel
LED indicator light indicates battery life
Power provided by LR6/AA size alkaline battery
Three optional transmitters: bodypack, handheld and XLR plug-on transmitter
Includes a belt-pack transmitter, camera mountable receiver and an omnidirectional lavalier microphoneOperating Frequencies:
Channel A Channel B Channel C Channel D
203.65MHz 207.75MHz 211.55MHz 215.35MHz
Transmitters:
Operating Frequencies: 203-216MHz
Modulation Frequency: Modulation
Signal to noise ratio: 70dB or more
Antenna: 1/8λ wire antenna
Voice delay: 12ms
Battery: LR6/AA size alkaline Battery (not included)
Battery Life: 5 hours
Audio input connector: mini XLR
Current Consumption: 150 mA
Dimensions: L102*W62*H44.7 mm
Weight: 80g (2.8 oz) without battery
Receiver:
Operating Frequencies: 203-216MHz
Reception System: FM Superheterodyne
Reception Sensitivity: 2 µV for 30 dB S/N
Output Connector: 3.5 mm (1/8″) TRS
DC Input: 9V DC (center-positive)
Battery: LR6/AA size alkaline Battery (not included)
Current Consumption: 150 mA
Battery Life: 5 hours
Dimensions: 102 x 62.0 x 44.7
Antenna Length: 178mm
Weight: 80 g (2.8 oz) without battery
3,000 EGPAdd to cart
Two balanced XLR inputs One monitor input jack
One stereo 1/8″ (3.5 mm) mini-jack output
Left and Right control knobs allows you to adjust the signal of each channel to the optimum recording levels
M/S Switch select mono or stereo output mode
LINE / MIC/ PH Switches
PH 12V/OFF/48V Switch
Level Meter indicates the sound level in dB for each channel
The LED signal indicators flash red for overload
Gain switch selects LOW for unity gain or HIGH for +20dB boost in sound level
Headphone jack to monitor the audio from microphones or camera
AGC ON/OFF Switch —Auto Gain Control will increase the gain to maximum level, the AGC Disable function reduces the hiss when the camera is recording during quiet moments
GND1/GND2 Dual-mode grounding switch
Dual Headphone Jacks allow you to monitor the audio from the adapter at the input and output points Maximum Input Levels:
MIC 0 dB on the Level meter at -44 dBu input
LINE 0 dB on the Level meter at +10 dBu input
Output Level:Nominal MIC levels
Frequency Response:20 Hz to 20 kHz (+/- 0.5 dB)
THD:Less than 0.01% @ 1kHz, -30dBu input
S/N Ratio:85 dB @ 1 Khz, -30 dBu input
Gain:
LO gain: 0 dB
HI gain: 20 dB
Phantom Power:
Dual regulated 12 or 48 volt power supplies
Current to 14 mA (direct short)
Level meter:
-18 to +3 dB in 3 dB increments
Battery Type:One 9 volt alkaline or lithium battery
Battery Duration:
3 hours typical with alkaline battery (no phantom)
8 hours typical with lithium battery (no phantom)
Dimensions:
(L x W x H) 155 mm x 98 mm x 64 mm
Weight:21.1 oz (0.599 kg)
4,750 EGPAdd to cart
• Transducer Principle: Back Electret Condenser
• Directivity Characteristic: Hyper-cardioid
• Frequency Response: 40Hz-16kHz
• Sensitivity: -36dB±3dB (0dB=1V/Pa at 1kHz)
• Output Impedance: 100Ω±30% (at 1kHz)
• Equivalent Noise Level: ≤26dB A (IEC 581-5)
• Max. Input SPL: 130dB (THD ≤1.0% at 1kHz)
• Bass Filter: 10dB/octave at 80Hz
• Power Requirements: 9-52V DC Phantom Power
1,450 EGPAdd to cart
Cardioid broadcast sound quality
1400 mAh internal rechargeable lithium battery
Balanced output
+48V phantom power
High frequency boost button
High pass filter (150 Hz)
Signal to noise ratio:75 dB SPL (per IEC651)
-10 dB PAD button Acoustic Principle:Line gradient
Directional Pattern:Cardioid
Frequency Range:40 to 20k Hz (selectable HPF 150 Hz)
Sensitivity:-35±3dB(0dB=1V/Pa,at 1KHz) 1.5V 2.2kΩ
Output Impedance:200 ohm
Maximum Output:10 dBu (at 1 kHz, 1% THD into 1 kOhm)
Dynamic Range:119 dB (per IEC651)
Maximum SPL:135 dB
Signal to Noise Ratio:75 dB SPL (per IEC651)
Power:48V phantom power;
built-in lithium battery;
(battery life:150 hours)
Output Connection;
3-pin XLR
balanced output between Pin 2 (+)
Pin 3 (-) and Pin 1 (ground)
Dimensions:2.3 x 2.3 x 28.2 cm
Weight:171g (About 6 oz.)
Maximum SPL:135 dB
7,250 EGPAdd to cart
XLR connector
+48V phantom power
Records 24bit/48kHz wav audio
Easy-to-use menu and LCD display
Input audio control
Switchable low-cut filter
3.5mm headphone monitor output
Lightweight all-metal construction Recording Media:
micro SD card (64MB~2GB)
microSDHC card (4GB~32GB)
Recording/Playback Format:24/48kHz 16/24bit, mono/poly BWF
Recording/Playback Format:24/48kHz 16/24bit, mono/poly BWF
Input Connector:XLR jack (Female), 1GND;2HOT;3COLD
Mic Input Level:Selectable at -12dBu~+33dBu
Headphone Jack:1/8’’ (3.5mm)
Frequency Response:20Hz~22kHz +/-2dB
Distortion:0.05% (1kHz sine wave)
S/N ratio:92dB or higher
Battery Type:2x AA Battery (alkaline, NiMH or lithium)
Power Consumption:0.65W (Maximum)
Phantom Power:+48V
3,650 EGPAdd to cart
Two pro-standard XLR terminals
Two real time audio level controls
LINE/MIC/48V PH switches
Three level gain controls (0dB, 10dB, 20dB)
Sandard cold shoe mount
Low cut switch (150Hz) Inputs:2x Balanced XLR inputs
Output:3.5mm TRS (for Cameras & Camcorders)
Power Requirements:9V Battery
Frequency Response:20 Hz to 20 kHz, +/-0.5 dB
SNR:80 dB @ 1 kHz, -30 dBu input
Dimensions (WxHxD)
XLR Adapter: 3.3 x 3.9 x 3.3″ (84 x 100 x 83mm)
Microphone: 1.7 x 7.4″ (43 x 187mm)
Weight:
XLR Adapter: 5.9 oz (167g)
Microphone: 2.1 oz (60g)
7,000 EGPAdd to cart
Optimised frequency response
Extreme low handling and wind noise
Excellent sound quality
Cardioid dynamic capsule
Rugged all-metal body Pick-up pattern:cardioid
Frequency Response:100Hz~10KHz
Sensitivity:0°~-52.4dB±3dB (0dB=1V/ubar at 1KHz)
Output Impedance:500Ω±30% at 1 KHz
Connector:3-pin XLR Connector
Dimensions:ø51 mm,length 258mm/approx.320g
4,250 EGPAdd to cart
Two pro-standard XLR terminals
Two real time audio level controls
LINE/MIC/48V PH switches
There level gain controls (0dB, 10dB, 20dB)
Standard cold shoe mount
Low cut switch (150Hz)
LED Indicator input Connections: 2 x XLR balanced – Mic/Line
(included SR-NV5 microphone takes up 1 input, if used)
Output Connection: 1 x 1/8″ (3.5 mm) wired connector
Power Requirements: 9 V alkaline or lithium battery
Frequency Response: 20 Hz to 20 Khz, +/-0.5 dB
THD: Less than 0.01% @ 1 kHz, -30 dBu input
SNR: 80 dB @ 1 kHz, -30 dBu input
Dimensions: XLR adapter (WxHxD)
3.31’’ x 3.94’’ x 3.27″ (84 x 100 x 83 mm)
Weight: XLR adapter: 5.9 oz (167g)
3,250 EGPAdd to cart
Improves audio quality of smart phone
Two 1/8’’ (3.5mm) stereo mic/line inputs
One mini XLR microphone input (a mini-XLR to standard-XLR cable included)
+48V phantom power
One 1/8’’ (3.5mm) stereo line output to phone
One 1/8’’ (3.5mm) headphone monitor output
PLAY/REC monitor switch
Independent L/R level meters
Volume control knob
Includes two plug-in power condenser microphones
Includes a device holder and aluminum hand grip
Power provided by 9V battery Frequency Response: 20 Hz to 20 Khz, +/-0.5 dB
SNR: 82 dB @ 1 kHz, -30 dBu input
Distortion: Less than 0.03% @ 1 kHz, -30 dBu input
INPUT 1 GAIN: 15 dB
INPUT 2 GAIN & MINI XLR Jack: 15 dB
INPUT 1 & INPUT 2 Power: 5V power supplies
MINI Jack Phantom Power: 48V power supplies
VU Meter: -18 dB to +3 dB in 3 dB increments
Power Requirements: 9V alkaline or lithium battery
Dimensions: L 95 x W35 x H298 mm
Weight: 0.74 kg (26.1 oz.)
3,000 EGPAdd to cart
1,000 EGPAdd to cart
© All copyrights reserved. Developed by Swarms Agency